SAQA All qualifications and part qualifications registered on the National Qualifications Framework are public property. Thus the only payment that can be made for them is for service and reproduction. It is illegal to sell this material for profit. If the material is reproduced or quoted, the South African Qualifications Authority (SAQA) should be acknowledged as the source.
SOUTH AFRICAN QUALIFICATIONS AUTHORITY 
REGISTERED UNIT STANDARD THAT HAS PASSED THE END DATE: 

Operate conversion equipment used for surfacing and thicknessing products in the dry timber processing area of lumber mill 
SAQA US ID UNIT STANDARD TITLE
264795  Operate conversion equipment used for surfacing and thicknessing products in the dry timber processing area of lumber mill 
ORIGINATOR
SGB Forestry 
PRIMARY OR DELEGATED QUALITY ASSURANCE FUNCTIONARY
-  
FIELD SUBFIELD
Field 01 - Agriculture and Nature Conservation Forestry and Wood Technology 
ABET BAND UNIT STANDARD TYPE PRE-2009 NQF LEVEL NQF LEVEL CREDITS
Undefined  Regular  Level 2  NQF Level 02  10 
REGISTRATION STATUS REGISTRATION START DATE REGISTRATION END DATE SAQA DECISION NUMBER
Passed the End Date -
Status was "Reregistered" 		 2018-07-01  2023-06-30  SAQA 06120/18 
LAST DATE FOR ENROLMENT LAST DATE FOR ACHIEVEMENT
2024-06-30   2027-06-30  

In all of the tables in this document, both the pre-2009 NQF Level and the NQF Level is shown. In the text (purpose statements, qualification rules, etc), any references to NQF Levels are to the pre-2009 levels unless specifically stated otherwise.  

This unit standard does not replace any other unit standard and is not replaced by any other unit standard. 

PURPOSE OF THE UNIT STANDARD 
The Unit Standard will be useful for people wish to complete at NQF Level 2 Learnership in lumber milling.

People credited with this Unit Standard are able to:
  • Understand the purpose and set up of conversion equipment used for surfacing and thicknessing products.
  • Set-up and operate conversion equipment used for surfacing and thicknessing products to the prescribed standards produce the required surfacing and thicknessing. 
    		•

    LEARNING ASSUMED TO BE IN PLACE AND RECOGNITION OF PRIOR LEARNING 
    A Learner who wishes to enter a learning programme for this Unit Standard must be able to demonstrate:
  • Competence in mathematical and communication skills equivalent to NQF Level 2.
  • An understanding of the detail of the lumber milling process, especially in the Dry Mill area.
  • Skills competencies equivalent to NQF Levels 1 of Dry Milling as required by the NQF Levels 1 Learnerships.
  • Workplace procedures, health and safety measures, and environmental management principles equivalent to NQF Level 1. 
    		•

    UNIT STANDARD RANGE 
    N/A 

    Specific Outcomes and Assessment Criteria: 

    SPECIFIC OUTCOME 1 
    Collect all the prescribed setting up tools and equipment and cutting tools (blades, knives) for the conversion equipment used for surfacing and thicknessing products. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    The availability of required tools for setting up conversion equipment used for surfacing and thicknessing products ensures successful execution of surfacing and thicknessing operations in the Dry Mill. 

    ASSESSMENT CRITERION 2 
    The correct tools for setting up the conversion equipment used for surfacing and thicknessing products are assembled timeously. 

    SPECIFIC OUTCOME 2 
    Set up the conversion equipment used for surfacing and thicknessing products and install the required cutting tools, to prescribed standards, in the prescribed manner. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    A correctly set up conversion equipment used for surfacing and thicknessing products ensures that dried lumber is converted in the most efficient manner. 

    ASSESSMENT CRITERION 2 
    Correct set up procedures for conversion equipment used for surfacing and thicknessing products are demonstrated. 

    SPECIFIC OUTCOME 3 
    Operate the conversion equipment used for surfacing and thicknessing products in the prescribed manner to produce lumber of the prescribed surfacing and thicknessing. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    Correct operation of the conversion equipment used for surfacing and thicknessing products ensures that dried lumber is converted into the correct dimensions and quality. 

    ASSESSMENT CRITERION 2 
    Conversion equipment used for surfacing and thicknessing products is safely operated according to company`s procedures. 

    SPECIFIC OUTCOME 4 
    Control the throughput and quality to maintain prescribed standards. 

    ASSESSMENT CRITERIA     

    ASSESSMENT CRITERION 1 
    Quality control measures are applied to ensure production of good quality products. 

    ASSESSMENT CRITERION 2 
    The correct throughput of surfacing and thicknessing products are achieved. 


    UNIT STANDARD ACCREDITATION AND MODERATION OPTIONS 
  • An employed individual who wishes to be assessed against this Unit Standard may apply to, or inform, the relevant responsible person in the relevant workplace, to request management to arrange for the assessment by the relevant assessor accredited for this purpose by the ETQA of the FIETA. An unemployed Learner must arrange with the training provider for assessment.
  • Anyone assessing a Learner against this Unit Standard must be registered as an assessor for this purpose by the ETQA.
  • The manner/method and source of providing the learning that will enable compliance with the requirements of this Unit Standard, must be accredited by the ETQA.
  • Moderation of the assessment will be performed in the manner and by the moderator(s) accredited for this purpose by the ETQA.
  • Assessment can be performed by means of oral testing, written tests and on-the-job observation. Formative assessment can be carried out during and after achievement of each specific outcome, and summative assessment at the conclusion of the training programme for this Unit Standard. Assessment will take place at a venue or workplace designated by the relevant assessor(s). 
    		•

    UNIT STANDARD ESSENTIAL EMBEDDED KNOWLEDGE 
    The Learner will be have acquired the detailed knowledge and understandig of and skills relating to:
  • The setting up of conversion equipment used for surfacing and thicknessing products and installation of appropriate cutting tools, to prescribed standards.
  • The operation of conversion equipment used for surfacing and thicknessing products as well as ancillary material handling equipment.
  • The maintaining product dimension and process throughput standards.
  • The routine maintenance of the conversion equipment used for surfacing and thicknessing products as well as ancillary materials handling equipment.
  • Competence in mathematical and communication skills equivalent to NQF Level 2.
  • Competence in work procedures, safety and health measures, and environmental management principles equivalent to NQF Level 2. 
    		•

    UNIT STANDARD DEVELOPMENTAL OUTCOME 
    N/A 

    UNIT STANDARD LINKAGES 
    N/A 


    Critical Cross-field Outcomes (CCFO): 

    UNIT STANDARD CCFO IDENTIFYING 
    Identify and use the correct the conversion equipment used for surfacing and thicknessing products. 

    UNIT STANDARD CCFO WORKING 
    Contribute towards setting up of conversion equipment used for surfacing and thicknessing products and installation of appropriate cutting tools, to prescribed standards. 

    UNIT STANDARD CCFO ORGANISING 
    Organise operation of the conversion equipment used for surfacing and thicknessing products as well as ancillary material handling equipment. 

    UNIT STANDARD CCFO COLLECTING 
    Collate and analyse data in relation to dimension and process through put standards. 

    UNIT STANDARD CCFO COMMUNICATING 
    Communicate health and safety requirements. 

    UNIT STANDARD CCFO SCIENCE 
  • Use equipment in a safe manner with due regard to operator`s manuals.
  • Assume full responsibility for all tools and instruments used for the conversion equipment used for surfacing and thicknessing products of the Dry Mill. 
    		•

    UNIT STANDARD ASSESSOR CRITERIA 
    N/A 

    REREGISTRATION HISTORY 
    As per the SAQA Board decision/s at that time, this unit standard was Reregistered in 2012; 2015. 

    UNIT STANDARD NOTES 
    N/A 

    QUALIFICATIONS UTILISING THIS UNIT STANDARD: 
      ID QUALIFICATION TITLE PRE-2009 NQF LEVEL NQF LEVEL STATUS END DATE PRIMARY OR DELEGATED QA FUNCTIONARY
    Core  66269   General Education and Training Certificate: Lumber Milling  Level 1  NQF Level 01  Passed the End Date -
    Status was "Reregistered"     		 2023-06-30  FPMSETA 
    Elective  66312   National Certificate: Lumber Milling  Level 2  NQF Level 02  Passed the End Date -
    Status was "Reregistered"     		 2023-06-30  FPMSETA 


    PROVIDERS CURRENTLY ACCREDITED TO OFFER THIS UNIT STANDARD: 
    This information shows the current accreditations (i.e. those not past their accreditation end dates), and is the most complete record available to SAQA as of today. Some Primary or Delegated Quality Assurance Functionaries have a lag in their recording systems for provider accreditation, in turn leading to a lag in notifying SAQA of all the providers that they have accredited to offer qualifications and unit standards, as well as any extensions to accreditation end dates. The relevant Primary or Delegated Quality Assurance Functionary should be notified if a record appears to be missing from here.
     
    1. ASSURED VOCATIONAL SKILLS INSTITUTE PTY LTD 
    2. SINOVUYOLETHU TRADING PTY LTD 
    3. TIRHANI SKILLSTRAINING PTY LTD 
    4. VEB CELE & ASSOCIATES PTY LTD 


    All qualifications and part qualifications registered on the National Qualifications Framework are public property. Thus the only payment that can be made for them is for service and reproduction. It is illegal to sell this material for profit. If the material is reproduced or quoted, the South African Qualifications Authority (SAQA) should be acknowledged as the source.