SAQA All qualifications and part qualifications registered on the National Qualifications Framework are public property. Thus the only payment that can be made for them is for service and reproduction. It is illegal to sell this material for profit. If the material is reproduced or quoted, the South African Qualifications Authority (SAQA) should be acknowledged as the source.
SOUTH AFRICAN QUALIFICATIONS AUTHORITY 
REGISTERED UNIT STANDARD THAT HAS PASSED THE END DATE: 

Maintain and repair three phase AC machines and control gear 
SAQA US ID UNIT STANDARD TITLE
10262  Maintain and repair three phase AC machines and control gear 
ORIGINATOR
SGB Electrical Engineering & Construction 
PRIMARY OR DELEGATED QUALITY ASSURANCE FUNCTIONARY
-  
FIELD SUBFIELD
Field 12 - Physical Planning and Construction Electrical Infrastructure Construction 
ABET BAND UNIT STANDARD TYPE PRE-2009 NQF LEVEL NQF LEVEL CREDITS
Undefined  Regular  Level 4  NQF Level 04  12 
REGISTRATION STATUS REGISTRATION START DATE REGISTRATION END DATE SAQA DECISION NUMBER
Passed the End Date -
Status was "Reregistered" 
2007-04-03  2009-02-18  SAQA 0160/05 
LAST DATE FOR ENROLMENT LAST DATE FOR ACHIEVEMENT
2010-02-18   2013-02-18  

In all of the tables in this document, both the pre-2009 NQF Level and the NQF Level is shown. In the text (purpose statements, qualification rules, etc), any references to NQF Levels are to the pre-2009 levels unless specifically stated otherwise.  

This unit standard is replaced by: 
US ID Unit Standard Title Pre-2009 NQF Level NQF Level Credits Replacement Status
259177  Maintain, test and repair AC machines and control gear  Level 4  NQF Level 04  12   

PURPOSE OF THE UNIT STANDARD 
This unit standard is for persons in the Electrical Engineering; Generation; Distribution; Transmission, Construction and Renewable Energy Sector

A person credited with this unit standard will understand and be able to:
Isolate, maintain, repair and do fault finding on a range of three phase AC machines and control gear.

This unit standard will contribute to the full development of the learner within the electrical engineering and construction environment by providing recognition, further mobility and transportability within the field of Physical Planning and Construction.The skills, knowledge and understanding demonstrated within this unit standard are essential for social and economic transformation and upliftment within the electrical engineering and construction environment. 

LEARNING ASSUMED TO BE IN PLACE AND RECOGNITION OF PRIOR LEARNING 
The following knowledge, skills attitude and / or equivalent:
  • Applicable statutory requirements
  • Use of basic hand tools and portable power tools
  • Use of relevant testing and measuring equipment
  • Maintain and repair single phase AC machines and control gear
  • Install and commission three phase AC machines and control gear 

  • UNIT STANDARD RANGE 
    Isolating procedures according to SABS 0142/0108

    Three phase AC Machines include, but are not limited to:
  • Induction motors, slip-ring motors and alternators

    All work to be carried out under direct supervision

    Testing and measuring equipment include but are not limited to:
  • Multimeters, Insulation tester, Clip-on ammeter

    Statutory Requirements Definition:
  • Statutory requirements may include but are not limited to OHS Act, SABS Regulations, Mineral Act, Local Authority requirements, Manufacturers specifications and Worksite procedures

    Control gear may include but is not limited to:
  • Direct on line, star delta, soft starter/ drivers / inverters, sequence / resistance starters, forward & reverse, rotary switch, auto transformer and dual speed 

  • Specific Outcomes and Assessment Criteria: 

    SPECIFIC OUTCOME 1 
    Prepare to maintain and repair three phase AC machines and control gear. 

    ASSESSMENT CRITERIA
     

    ASSESSMENT CRITERION 1 
    1. Job instructions and applicable electrical drawings are obtained, evaluated and the sequence of operation is determined. 

    ASSESSMENT CRITERION 2 
    2. Appropriate tools and personal protective equipment are identified, selected and evaluated according to safety requirements. 

    ASSESSMENT CRITERION 3 
    3. Safety - and - work site procedures are obtained according to job requirements. 

    ASSESSMENT CRITERION 4 
    4. Permission is obtained to carry out task according to instructions and drawings. 

    ASSESSMENT CRITERION 5 
    5. Three phase AC machines and associated control gear are identified and isolated according to maintenance procedures. 

    ASSESSMENT CRITERION 6 
    6. Work site is analyzed for safety hazards and corrective actions taken according to statutory requirements. 

    SPECIFIC OUTCOME 2 
    Maintain three phase AC machines and control gear. 

    ASSESSMENT CRITERIA
     

    ASSESSMENT CRITERION 1 
    1. Personal protective equipment is used and site safety procedures are adhered to throughout maintenance. 

    ASSESSMENT CRITERION 2 
    2. Appropriate tools and test equipment are selected, analyzed and used correctly as per manufacturers specifications and work site procedures. 

    ASSESSMENT CRITERION 3 
    3. Task instructions, and work site procedures are followed correctly. 

    ASSESSMENT CRITERION 4 
    4. Testing and measuring is carried out and results evaluated according to maintenance procedures. 

    ASSESSMENT CRITERION 5 
    5. Three phase A.C. machines and control gear are maintained according to manufacturer's specifications and maintenance procedures. 

    ASSESSMENT CRITERION 6 
    6. The correct site approved cleaning materials and solvents are utilised during maintenance. 

    SPECIFIC OUTCOME 3 
    Carry out fault finding and repairs on three phase AC machines and control gear. 

    ASSESSMENT CRITERIA
     

    ASSESSMENT CRITERION 1 
    1. The sequence of the operation is analyzed according to circuit diagram and manufacturer`s specifications. 

    ASSESSMENT CRITERION 2 
    2. Appropriate measuring and testing equipment are selected and applied correctly 

    ASSESSMENT CRITERION 3 
    3. Relevant information is gathered by making use of logical methods according to the correct fault finding techniques and safety procedures. 

    ASSESSMENT CRITERION 4 
    5. Reasons for following the correct safe work procedures are understood and the consequences of non-conformance are accurately explained. 

    ASSESSMENT CRITERION 5 
    4. Faults are safely repaired according to work site procedures and gathered information. 

    SPECIFIC OUTCOME 4 
    Conclude maintenance and repairs on three phase AC machines and control gear. 

    ASSESSMENT CRITERIA
     

    ASSESSMENT CRITERION 1 
    1. Work area is restored to serviceable condition according to statutory requirements 

    ASSESSMENT CRITERION 2 
    2. Pre-commissioning quality checks are conducted after maintenance and necessary corrective action is taken 

    ASSESSMENT CRITERION 3 
    3. Machine and control gear is restored to normal operating conditions 

    ASSESSMENT CRITERION 4 
    4. Records are accurately completed, drawings returned to source and reports effectively communicated according to work site procedures 

    ASSESSMENT CRITERION 5 
    5. Tools and equipment are examined, cared for and stored according to statutory requirements 

    ASSESSMENT CRITERION 6 
    6. Waste material are disposed of according to environmental standards and work site procedures 


    UNIT STANDARD ACCREDITATION AND MODERATION OPTIONS 
    1. Anyone assessing a learner against this unit standard must be registered as an assessor with the relevant ETQA.
    2. Any provider offering learning that will enable achievement of this unit standard must be accredited as a provider through the relevant ETQA.
    3. Moderation of assessment will be overseen by the relevant ETQA according to the moderation guidelines in the relevant qualification and the agreed ETQA procedures. 

    UNIT STANDARD ESSENTIAL EMBEDDED KNOWLEDGE 
  • Prescribed isolating procedures.
  • Identification and functions of relevant components.
  • Correct application of relevant hand tools.
  • Proper usage of relevant testing and measuring equipment.
  • Names, locations and functions of appropriate tools
  • Safety related to each tool
  • Care and storage of tools 

  • UNIT STANDARD DEVELOPMENTAL OUTCOME 
    N/A 

    UNIT STANDARD LINKAGES 
    N/A 


    Critical Cross-field Outcomes (CCFO): 

    UNIT STANDARD CCFO IDENTIFYING 
    Identify, evaluate and solve problems in isolating, maintaining, repairing and doing fault finding. 

    UNIT STANDARD CCFO WORKING 
    Work effectively with others during the isolating, maintaining, repairing and fault finding process. 

    UNIT STANDARD CCFO ORGANISING 
    Organise and manage oneself in planning the work and determining a sequence of operation. 

    UNIT STANDARD CCFO COLLECTING 
    Collect, analyse, organise and critically evaluate information obtained during isolating, maintaining, repairing and fault finding processes. 

    UNIT STANDARD CCFO COMMUNICATING 
    Communicate with fellow workers and involved parties, the interpretation and reporting processes. 

    UNIT STANDARD ASSESSOR CRITERIA 
    N/A 

    UNIT STANDARD NOTES 
    This unit standard has been replaced by unit standard 259177, which is "Maintain, test and repair AC machines and control gear", Level 4, 12 credits.

    This Unit Standard was originally registered on 12 June 2002 under SAQA decision number 0742/02. It has been re-registered on 11 February 2004 under SAQA 2552/04.


    Supplementary information

    Specfied requirements
  • SABS 0142
  • OHS Act

    Credits
    Total hours required by the learner to achieve the required outcomes:

    Activity Hours
    Classroom learning 30
    On-the-job learning 40
    Self directed learning 25
    Coaching required 25
    Other

    Total 120

    Credits achieved: 12 

  • QUALIFICATIONS UTILISING THIS UNIT STANDARD: 
      ID QUALIFICATION TITLE PRE-2009 NQF LEVEL NQF LEVEL STATUS END DATE PRIMARY OR DELEGATED QA FUNCTIONARY
    Core  48474   National Certificate: Electrical Engineering  Level 4  Level TBA: Pre-2009 was L4  Passed the End Date -
    Status was "Reregistered" 
    2009-02-18  Was EWSETA until Last Date for Achievement 
    Elective  58288   National Certificate: Electro-Mechanics  Level 3  NQF Level 03  Passed the End Date -
    Status was "Reregistered" 
    2023-06-30  As per Learning Programmes recorded against this Qual 


    PROVIDERS CURRENTLY ACCREDITED TO OFFER THIS UNIT STANDARD: 
    This information shows the current accreditations (i.e. those not past their accreditation end dates), and is the most complete record available to SAQA as of today. Some Primary or Delegated Quality Assurance Functionaries have a lag in their recording systems for provider accreditation, in turn leading to a lag in notifying SAQA of all the providers that they have accredited to offer qualifications and unit standards, as well as any extensions to accreditation end dates. The relevant Primary or Delegated Quality Assurance Functionary should be notified if a record appears to be missing from here.
     
    NONE 



    All qualifications and part qualifications registered on the National Qualifications Framework are public property. Thus the only payment that can be made for them is for service and reproduction. It is illegal to sell this material for profit. If the material is reproduced or quoted, the South African Qualifications Authority (SAQA) should be acknowledged as the source.